Recent content by bhodisatva
-
Free wheeling hubs???
Yes 10 or 24 spline free wheel hubs will fit your series vehicle, depends which half shafts you have got which ones you go for though. Generally series II vehicles have the coarser 10 spline ends with series III's having 24 spline ends. However, the only real way to tell is to get the hub ends...- bhodisatva
- Post #3
- Forum: Series
-
Lean/Tilt to the Right
Sounds like the springs have been put on the wrong side. Most springs are handed and the drivers side should when viewed from behind or the front sit higher than the passenger side.- bhodisatva
- Post #4
- Forum: Series
-
Chat?
There are a couple of options open to vBulletin software users for a chat section that i know of. We have one version running over on LRUK Forums, called a shoutbox, but i know there are fully fledged chat programs such as mIRC that can be hooked up to the site. Good idea or bad, there's pro's...- bhodisatva
- Post #2
- Forum: Freelander Forum
-
Speedo woes
Check also at the gearbox end, there should be three screws holding the speedo cable in place, if one of these is missing it can give similar symptoms.- bhodisatva
- Post #3
- Forum: Series
-
My new SIII
Hi, and congratulations on your new puchase:). Unfortunately there's no real easy way to find out if your cylinder head is unleaded or not. If you have a receipt maybe you could contact the suppliers?, 1997 seems a bit early to have replaced it for unleaded to me though as over here in the UK...- bhodisatva
- Post #2
- Forum: Series
-
mmmmmmmmmmmmm nice :)
Spotted at the Land Rover owner show at the weekend.- bhodisatva
- Thread
- Replies: 24
- Forum: Discovery
-
24 Volt Series
Waaaaaaaay cool JC, i'm sure your gonna get to love your series shed as much as we love ours. Post some piccies when you take delivery of it, so's we can all see what she loks like. Have you thought of a name for her yet?- bhodisatva
- Post #10
- Forum: Series
-
series 3 electrics
Just a quick reply on this for the time being, will have a look in depth later..... But ....... have you checked all your earth (ground) connections?- bhodisatva
- Post #2
- Forum: Series
-
How many series owners do we have..?
Set up a thread, we'll get it stickied so it stays at the top. Just make your posts/updates as normal and upload the photo's to the post. That way we get to see your comments and the photo's.- bhodisatva
- Post #7
- Forum: Series
-
How many series owners do we have..?
Hello and welcome to the forums Ak. Do you have a digi camera, wanna give us a regular update on work and how it progresses?. If you feel you want to then i can always ask nicely and get the thread stickied so you can add to it at your leisure. Regards Roy.- bhodisatva
- Post #5
- Forum: Series
-
Hello folks
Good luck and welcome to Land Rover ownership. If you need any advice for the clutch gimme a yell in the series section. Roy.- bhodisatva
- Post #9
- Forum: Introduction
-
Hello folks
Series I 1948 - 1958 Series II/IIa 1958 - 1971 Series III 1971 - 1985 90/110 1983 - 1989 If you want the exact build date, contact... Eric Pagan senior engineer Land Rover Traceability Lode Lane West Midlands B92 8NW England UK. You will need to...- bhodisatva
- Post #5
- Forum: Introduction
-
How many series owners do we have..?
As it says, got to wondering how many series owners we got on the forum?- bhodisatva
- Thread
- Replies: 88
- Forum: Series
-
Jack
http://www.autosupplyusa.com/3tonfloorjack.html. This is the sort of jack i'd go for Melissa for the jobs you want to do. Three ton capacity and extra lift, should suit you down to the ground. http://www.autosupplyusa.com/3tonfloorjack.html- bhodisatva
- Post #10
- Forum: Reviews of Tools
-
Greetings from Los Angeles
Welcome to the forum Screehopper.- bhodisatva
- Post #10
- Forum: Introduction
