Recent content by maxx4wd
-
Upper Ball Joint Replacement / Tool size needed - tried searching
Honestly I don't recall where I got the ball joint from...probably O'Reilly's or Autozone...maybe carparts.com lucky8 maybe...britishpartsofutah...but I know I didn't buy it from the dealer as they wanted like 150 or something stupid like that... -
LR3 3/4 Frontrunner Slimline II FS
This is what it looks like installed. -
LR3 3/4 Frontrunner Slimline II FS
Frontrunner 3/4 Slimline II aluminum roof rack and accessories up for sale. I finally had a second to go through the garage and found some Landrover parts that needs a new home. More posts to come with some extra parts but first up is the... -
-
FS: GAP IID Tool BT
I only used it three times because I was previously using RSW software which was fine but I couldn’t pinpoint my problem with it and this was able to identify the issue first time. Then we decided to sell the LR3 so I no longer have a use for it any longer. We just traded the car so I wasn’t... -
FS: GAP IID Tool BT
Selling a like new Gap diagnostic IId tool, Bluetooth version G3 (used literally 3 times). Works and looks brand new. no longer have the vehicle so this essential item is up for grabs. It has been registered to my land rover, so you'll need to buy a new license/transfer ownership for $36 from... -
Lifted lr4 alignment question
I'm right with you with almost all your mods - I'm running 2.5" all around with 32s but I still have tire wear issues, so I'm interested to see if anyone has heard of a shim kit for these vehicles but my guess is we're just out of luck if we lift it. All I know is my 60k nittos are probably... -
Suspension problems after compressor and front structs replacement
I used this one but sure its about the same as anywhere else. https://www.britishpartsofutah.com/Range-Rover-Sport-LR3-LR4-Valve-Block-Seal-O-Ring-p/rcrvhk.htm -
Lower Control Arm ball-joint
I just pressed out the upper ball joints a month or two ago (using the O'Reilley's ball joint press and some elbo grease - note that this one doesn't have the perfect cups sized for reinstall so I had to use a deep socket from my toolbox for re-install opposed to the rental tools provided... -
LR3 2008 Suspension Height Sensor Linkage
Let me know if you still need that rear measurement - I just swapped out my failing stock ride height sensors in the rears and it came with the rubber ones that were about the same length as my Johnson rods for the rears (which is kinda funny as I remember them being shorter all the way around... -
Roof Rack Roof Top Tent
We sport the Frontrunner roof rack for the last few years and love it - easy to add/remove accessories - easy to put together and build quality is good - has quick mount tent mounts available but you'll have to check your specific RTT. I'm also contemplating adding a tent but haven't done so on... -
Broken coolant return ****** and fix
I actually cracked the radiator pipe connection but luckily it only cracked and I was able to JB weld it back when I slapped on new hoses...Will be adding a new Rad and probably trans cooler when I open it up next. gotta love aging plastics and rubber on these beasts... -
Upper Ball Joint Replacement / Tool size needed - tried searching
Just an update...I ended up renting the ball joint press from O'Reilly's Auto - (can't recall what brand it was) but after removing the threaded screw cap I was able to get the ball joint pressed out. The threads were too long to fit within the press so this ended up working great (sorry I was... -
Current info on installing back up camera?
Thanks for that info...it's certainly worth a shot and see what can / can't be displayed by looping that line...some use may be better than nothing...I do still have the head unit but I'm not sure where I could hide it but at a minimum I'm definately going to try to loop that optical cable. -
Suspension problems after compressor and front structs replacement
Yes the center valve block could be the problem but since you state that the rears deflate first I would look at that rear valve block. Sounds like what my front was doing about 2 years ago. The problem I had was the valve block was leaking back into the tank so it was an issue with the oring...
