Search results
-
F
Increased Performance
With the clearance issues, are you concerned at all about damaging the EAS system? I was considering getting rock/tree sliders as my first underbody armor, but it looks like you don't have either from your pictures, but you have the control arm skids. -
F
Long crank, no faults
Partial throttle will rev the engine, I found out when wearing my winter boots and pressing on the brake pedal also happened to press on the gas. I was surprised by how much higher than normal the engine revved. -
F
BCM SDD Questions
Knowing nothing about this, I would expect firmware images to be based on the board model/revision numbers and not model year. At least that's how I would design the system... -
F
Increased Performance
I just switched from the poly bushings to the OEM ones and it is a very noticeable improvement in ride quality. -
F
LR4 Front Fender Modification for Larger Tires
Yes, people have cut and welded it. The only negative would be a departure from the factory intended crash worthiness - the frame horn there is intended to keep the wheel from intruding on the footwell in a crash. While you may no longer rub with your 2" lift, you will rub if you ever have a... -
F
gallery pressure
That's temperature shutdown, when the compressor reaches 130*C, it then waits for temps to drop back to 110*C and starts up again. It does look like there's a pressure drop from when it shuts down to when it starts up, but that could be due to temperature change too due to the air cooling and... -
F
gallery pressure
I logged the change to off-road height with the new compressor. For reference here's the old: And with the new compressor: Doesn't look all that different. -
F
gallery pressure
I installed the new compressor on Sunday and logged the reservoir being filled again. I also have a log of the old compressor doing the same, though I didn't log the full fill of the reservoir, only up to the first thermal cutoff. Old: New: I haven't had a chance to log a normal to... -
F
Rear Wiper
it only does this if you have the front wipers on (even in rain sense). It is useful. My same vintage VWs do the same. -
F
gallery pressure
If you view the graph in the IID tool (rather than numeric data) you'll have a chance to see the data trends (including elapsed time). But if it's less than a minute, it sounds like my compressor might indeed be tired. -
F
bad lower ball joint lead to howling?
Also, the second side went *much* faster as I didn't have to pause to go watch videos for how to hammer the hub out of the knuckle. I printed out the relevant pages from the workshop manual and just followed along. -
F
gallery pressure
Any idea how quickly you got back to 250psi after the height change? -
F
gallery pressure
I failed to capture the startup sequence, you have to turn the ignition on, start the live capture, and then crank the engine... I did get the height change, but the system properly pressurized. So the height change took 5-10 seconds, then about two minutes to reach 1720 kPa (250psi) again. -
F
gallery pressure
I ordered a new Hitachi for $480 delivered, should be here Monday. I was logging gallery pressures yesterday and tried searching for that term but came up largely empty handed. I figured leaving some data that comes up in searches might help someone in the future. Strangely I did not get many... -
F
2016 LR4 Suspension Issue
Found a supposedly genuine Hitachi on Amazon for $480. I will inspect it carefully before installing it to make sure it is genuine. If no Hitachi markings, I'll send it back. -
F
gallery pressure
I was hoping to get some data points from the community regarding gallery pressure changes over time. Specifically, I'd like the following data from folks that have an IID Tool and are inclined to document behavior: 1. From cold start, starting gallery pressure, ending gallery pressure and... -
F
2016 LR4 Suspension Issue
The center valve block actually just controls the flow to/from the reservoir. The gallery connects to the compressor and front/rear valve blocks and has a pressure sensor. The front and rear blocks have 3 valves - individual valves for each side, and a cross link valve. To inflate, if there's... -
F
bad lower ball joint lead to howling?
The two hubs were a $505 from Lucky8. I got extra axle nuts ($18), but it turns out the hubs come with, so that wasn't necessary. I had asked them and they said they didn't. No biggie. Things came apart easily, thankfully there are videos for how to knocking the hub out, as there's not a lot... -
F
2016 LR4 Suspension Issue
I had repressurized the system and gone for a test drive of my new hubs. This was raising from normal to off-road upon return, the back went up quickly (a handful of seconds), the front was measured in minutes. -
F
bad lower ball joint lead to howling?
I tried two indy shops that specialize in land rover. First time they sent me home because the lock but on the tie rod was frozen. Replaced both tie rods and went back, came back with the wheel off center. Took it back again and this time it came back even more crooked. Took it to another... -
F
2016 LR4 Suspension Issue
Yes, I'm suspecting the center valve block, if it can't store air in the tank then the compressor would be doing all the work. -
F
bad lower ball joint lead to howling?
Got the new Timken hubs installed and I'm happy to report that the noise is gone. There's still a clunk in the steering somewhere, but that's a problem for another day. -
F
2016 LR4 Suspension Issue
Happy to report the front didn't sag overnight, I'll put the splash shield back on tonight.
