Search results
-
P0526-17 (28) Fan speed sensor circuit - General electrical failure - circuit voltage above threshold
Update (both good and bad! but mostly good). I used the Autel MaxiAP AP200 and got the same code (P0526 but without the additional numbers); so I used it to clear the code, scanning again the code is gone and didn't come back, I then checked it with the GAP tool and see the same! Weird! I did... -
P0526-17 (28) Fan speed sensor circuit - General electrical failure - circuit voltage above threshold
Thank you. It is spinning freely, I did see others mention motor mounts but every time I've looked at the fan it's turning at the same speed as the pulley on which it mounts so I discounted this (I will off-course double check). It's weird that it doesn't show up in the LR manual, I swear... -
P0526-17 (28) Fan speed sensor circuit - General electrical failure - circuit voltage above threshold
Hi Folks, I've been fighting this one for a while now but this weekend tried getting to the bottom of the issue without success; here's the gap tool screen: Here's what I've tried so far: - Installed a new viscous fan (Mahle OEM) - no change - Checked, reseated, cleaned and applied... -
2010 LR4 Air suspension need advice
Yeah - that as well, I didn't find that terrible to be honest, just take your time! -
2010 LR4 Air suspension need advice
I didn't find the top mounting bolt that difficult on the compressor, in fact it pales in comparison to some of the other "bolt" experiences on this vehicle (thinking the rear suspension valve block air hose nut and valve cover rear bolts on the drivers side, + others!). Don't let this stop you... -
Replace the VVT Phasers when replacing chains on a '16 LR4
I opted not to do mine purely from a financial perspective; time will tell if it's an OK decision... I know with bike chains it's encouraged to swap out the cassette and front rings. I don't know how the stretching of the chain impacts the wear on the VVT's but I have to imagine that we're... -
2011 LR4 Suspension code U3000-1D
Awesome - well done and thanks for reporting back :) -
2011 LR4 Suspension code U3000-1D
Like many codes I fear! This is why I always try and leave a trail for others to follow... The ball is yours for this one! Please keep us posted. -
Beep beep
Page 4210 of the Manual has this: CJB = central junction box It sure seems there are a lot of Antennas! I'm thinking that the wiring diagram should have something in terms of the wiring but I'm not sure if this will help with the location of the antennas? Yesterday I had the key in my... -
2011 LR4 Suspension code U3000-1D
A quick search also yielded some other posts, does look like the U3000 is suspension related. https://www.disco3.co.uk/forum/post2378943.html https://www.landyzone.co.uk/land-rover/rr-sport-2010-air-compressor.378006/#post-5333187 https://www.rangerovers.net/threads/suspension-fault.352250/ -
2011 LR4 Suspension code U3000-1D
This U3000-1D doesn't mention suspension at all, could it be unrelated to your changes (other than the timing of the suspension raise request)? Is your battery OK? Bear in mind these things are super sensitive to dying batteries. I assume all the electrical connectors are OK? -
Beep beep
The phone blocking makes sense but the driver sides doesn't. I need to look at where the sensor is located in the vehicle and see if that's somehow impacting the behavior. Not sure yet what parts to be looking at... I thinking opening behavior is OK though, what's with that! -
Best way to clean out sunroof drains
In the sunroof area they're in the front corners, you see a little channel that leads to the hole but this is all really small stuff... The hole in the intake area can be found behind the foam block, it's not overly obvious so just keep looking you'll see it eventually. Top clean mine out I... -
Beep beep
Hey Folks - I mentioned this in the past but have a little more bandwidth at the moment to look at this issue... I notice that when pressing the button on the drivers door handle to lock the car I often get the "beep beep" noise and the car won't lock. If I move around ever so slightly in the... -
2010 LR4 Air suspension need advice
I'd also say it's a pretty subtle white residue, replace the o'rings, use a very small amount of silicon grease on the new ones and generally give the whole block a good blast with an air nozzle and wipe down all the internals. -
Sudden Hissing near Valve Cover (5.0 V8)
Replacement looks really easy so not a biggie! -
2010 LR4 Air suspension need advice
Why not just service the valve block, you'll save some $$$'s, have familiarity with the workings of the valve and honestly it's not that difficult. It's a pretty simple device so overall the mechanism portion of the valve block is unlikely to deteriorate over time, it's just the o'rings that... -
LR4 Window problems
Reset Procedure: "With the engine running. Windows closed. Lift up on the window switch, hold for 5 seconds and release. Repeat once." Worked beautifully, my drivers door window is behaving again. Thank you @Rover Range. With that I ran the test for @txfromwi, I can confirm there is a... -
Sudden Hissing near Valve Cover (5.0 V8)
Thanks for making me aware of the brake switch clicking noise, I was blissfully unaware until reading this thread and now I can "happily" report that I also have a loud clicking noise - great!!! :ahhhhh: -
LR4 Window problems
I'll test mine and report back once I've applied the reset. -
2010 LR4 Air suspension need advice
What parts are you thinking of in particular? For the compressor I went OE (AMK - bought and shipped from the UK as I believe I mentioned in the post above); for valve seal kits I believe it was Land Rover of Utah (it's posted in the thread above and I know others have had success with this...
