Recent content by El Solis
-
Compomotive PD 1881 finish delamination
I’ve had them since mid 2017. They’ve seen between 2-3 thousand off road miles. 90% or more was fire roads and nothing really technical and no rock crawling. I run 35psi off road in the rear (the affected area) and 50psi on road as I have my drawers and gear in the truck full time. Just had the... -
Compomotive PD 1881 finish delamination
Not only are most of mine delaminating (I have 6) but two just developed pin hole cracks on the inside next to the spoke. I was informed by Barry that this is due to under/over inflation however I don’t go below 35 psi (long story). He offered me two new ones at a slight discount (which I... -
Ton of faults after an aftermarket subwoofer was installed (SOLVED)
Don’t know if this is the answer but the stereo canbus system is tied into a bunch of car control stuff. Has something to do with safety, decreasing volume when backing up etc. The subwoofer install may have messed that up or worse they cut the canbus during the install [emoji51] Sent from my... -
Updated sources for skid plating?
I’ve got an Asfir front that’s taken some hits as I tend to lead and just installed the Asfir rear today after squishing my driver’s side exhaust. I’ve got the Tactical Rovers sliders and they are worth the weight. Sent from my iPhone using Tapatalk -
Combining spare-on-bumper with bike rack
I’m having a buddy weld a receiver hitch on my swing out so I can mount a bike rack there and keep the spare and access the rear cargo area. Waiting for the bike rack to ship but should have this done in April. Sent from my iPhone using Tapatalk -
Driver Seat Fuse
Mine just did this but I had one of my kids on my lap and I think it was too much for the motor. Did you have an inciting event or is it happening often? Sent from my iPhone using Tapatalk -
Phone Mount For LR4?
I combined a Quadlock wireless charger with a RAM mount suction cup mount. Easy enough. Can send parts list if interested. Sent from my iPhone using Tapatalk -
Jacking Options
Not sure if it will fit (I have one) but you’ll need a way to support the truck while you change out the extensions. I was working with Safe Jack to find a simple solution. I couldn’t. I have sliders and use their jack stand and it works fine but for stock trucks with only one jacking point at... -
Suspension fault driving fast on twisty mountain road
I’ve had it happen in off road height without rods or height manipulation. Usually when you hit a dip or with a drop that causes a rapid drop of a wheel. Lights stay on for a few seconds then clear. Once I had to wait until I turned off the car to let it reset. -
Suspension fault driving fast on twisty mountain road
Were you loaded up? Might have pushed a height sensor out of range on the twisty roads. I get that occasionally OffRoad, especially in off road height. GAP tool will tell you what tripped the fault, might not explain why it happened. -
Fueling frustration
My wife’s 15 Range Rover has this and it was a service recall. Dealer swapped the filler port as it was a known issue. -
Do i NEED a roof rack to get a waffle board?
You should check out Traction Jack as a waffle board. They fold in half and store in the rear cargo area nicely. Pics below. I’ve used mine for my LR4 and my Defender 110. I use them folded as I’ve seen them snap at the hinge in the middle. I’ve seen the work fully open too but that’s my... -
Question for LR4 owners that switched to 18" wheels
I run 265/65 BFG KO2s on compos without any rubbing. I’m not easy on my rig either. Haven’t had any issues. MY13 LR4 -
Jacking Options
The jack will tend to lean into the car as you are jacking. It can push the door skin in. I’ve seen it happen on more than one occasion, even with sliders. For this reason I don’t use the hi lift on my LR4. I carry the safe jack bottle jack and jack stand. I too have sliders and a steel bumper... -
Jacking Options
Careful with the hi lift as it will crease the door [emoji51] I use the safe jack system with the jack stand. They have a new stand but I don’t know if it works with the LR 3/4s.
