Search results
-
Buying a press to do my own wheel bearings....need advice on what else I need
Wheel bearings are sealed units. You won't need the race driver set. Front wheel bearings are bolted in. Rears are pressed in.- Rover Range
- Post #3
- Forum: LR3
-
Cooling System Replacement - Dealership.
These work great for prying up on the super charger.- Rover Range
- Post #16
- Forum: LR4
-
Cooling System Replacement - Dealership.
Normally aspirated would be 6 hrs.- Rover Range
- Post #10
- Forum: LR4
-
Cooling System Replacement - Dealership.
For the front , rear pipes and coolant pump. Labor is around 10hrs.- Rover Range
- Post #8
- Forum: LR4
-
Mid-life Crisis Accomplished
Good stuff my man. Especially with car payments hovering around, $800 a month.- Rover Range
- Post #2
- Forum: LR4
-
Third head gasket job- why are they failing?
Get one of these. https://www.scangauge.com/products/scangauge-ii/ Won't have to tap into the cooling system.- Rover Range
- Post #14
- Forum: LR4
-
Open to Suggestions
^^ Agreed. Starter bendix may be binding. Not fully retracting, keeping the starter drive gear out further than it should be.- Rover Range
- Post #95
- Forum: LR4
-
P0430 - Catalyst System Efficiency Below Threshold (Bank 2) - My car is running great
WTH? They promise our customers same day delivery. :oops:- Rover Range
- Post #12
- Forum: LR4
-
Open to Suggestions
Only "shield" is the bracket for the fuel lines.- Rover Range
- Post #91
- Forum: LR4
-
P0430 - Catalyst System Efficiency Below Threshold (Bank 2) - My car is running great
The cat convertor efficiency is reduced. They are covered under the emissions warranty for 8 years, 80k miles. Depending on your vehicle's in service date, may be covered.- Rover Range
- Post #2
- Forum: LR4
-
4.4 V8 Rear Coolant Leak
All the coolant pipes are in the front of the engine. Coolant may be running down under the intake manifold.- Rover Range
- Post #2
- Forum: LR3
-
AC Condenser Replacement Part Quality?
The open ports can be capped with plastic caps. Won't be an issue. Vacuuming the system after reassembly will remove any moisture.- Rover Range
- Post #2
- Forum: LR4
-
lowering suspension when not in use for weeks on end
I wouldn't lower it. All the suspension bushings will be in a bind. The suspension bolts are tightened at normal ride height.- Rover Range
- Post #2
- Forum: LR4
-
Any DIY tips out there on replacing a 2016 LR4 SCV6 Thermostat Housing?
For the piece broken off in the water pump. Carefully remove the black retaining ring. It just snaps in. Take a drywall screw and screw it into the broken of piece. Should only take a couple turns, by hand. Then slide out. Reinstall the locking ring.- Rover Range
- Post #18
- Forum: LR4
-
2014 Ford Escape to the Rescue.
Escape cam shafts fit the 2.0l engines.- Rover Range
- Post #4
- Forum: LR2
-
AC Fan Stopped While Driving
My guess would be the resistor. With the ignition off. Take the pollen filter out and see if you can rotate the blower fan easily.- Rover Range
- Post #2
- Forum: LR4
-
2011 5.0 head gaskets
Head gaskets, no guarantee. Used engine, don't know the history on it. New engine, expensive. But, you won't have to worry about any issues in the future.- Rover Range
- Post #2
- Forum: LR4
-
Keen location for FOB
Keep the fob in your pocket. No need to even pull it out.- Rover Range
- Post #5
- Forum: LR4
-
Rear left left height sensor supply
Ride height needs to be calibrated.- Rover Range
- Post #2
- Forum: Discovery
-
Third head gasket job- why are they failing?
Go with OEM head gaskets.- Rover Range
- Post #6
- Forum: LR4
-
Third head gasket job- why are they failing?
There's no requirement to retorque the head bolts after installation. The head gaskets leak due to not enough head bolts and little material between the cylinders. IMO. A long block is truly the best long-term fix.- Rover Range
- Post #3
- Forum: LR4
-
-
Open to Suggestions
Land Rover schematic shows WG and P wires go to the oil pump solenoid.- Rover Range
- Post #86
- Forum: LR4
-
Open to Suggestions
Post your VIN #. I check the Land Rover manual for the wiring orientation.- Rover Range
- Post #84
- Forum: LR4
-
Open to Suggestions
Yikes. The harness runs behind the motor mounts. Won't be fun trying to route the harness.- Rover Range
- Post #80
- Forum: LR4
