Search results
-
Looking to purchase timing chain tools
Damn! That is so kind of you, I ended up purchasing based on the links above. In the spirit of community I will commit to the same offer once I'm done with them. Thank you so much. -
Looking to purchase timing chain tools
Hey Folks, In the spirit of recycling things and before I head off to Amazon does anyone have either kit that they'd like to sale, I'm looking for two kits similar to these: Crankshaft Pulley Remover Installer Tool Kit Petrol Timing Tools (V8) 5.0L I'd be grateful for other suggestions as... -
LR4 Transmission Fluid Change: Pan Swap Option
Awesome - congratulations, you must have gotten your laptop resolved as well :) -
New alternator, must I calibrate in Gap for BMS? Also rock sliders install talk
Agreed with ftillier - take the bolt to a local reputable hardware store and ask them to identify the thread on the bolt (M8 or M10 by the look of it - but thread pitch is also important, e.g. M8 x 1.25); you then need a tap and a tap wrench: you then use this to clean up the threads, screw... -
Serpentine/Accessory belt failure on a very wet, dark MI road in the middle of nowhere...
Just to follow-up, with the cables swapped and a whole bunch of other experiments I still get the same readings... As ftillier points out, the temperature sensor is a thermistor which changes resistance with temperature; resistor type devices are typically not sensitive to direction of... -
Serpentine/Accessory belt failure on a very wet, dark MI road in the middle of nowhere...
I reread the temperatures, this is ignition on/engine off, initially I got this (which I suspect is why I aborted this the first time): Rather than going to quick list I went to the full list and was able to read the following (the engine hasn't been started today): I then realized I could... -
Serpentine/Accessory belt failure on a very wet, dark MI road in the middle of nowhere...
I didn't read them yet, I was under the impression that I couldn't get the temps without the engine running! Will look once I'm free of meetings - Thank you. -
Serpentine/Accessory belt failure on a very wet, dark MI road in the middle of nowhere...
"Are you sure the new ECT is giving you the reading on the left?" Yes I think so, it's the same sensor that was previously complaining about a circuit issue. For some reason it seems to be measuring hot when it's not; the pipe wasn't even hot to the touch. Perhaps the wires are the wrong way... -
Serpentine/Accessory belt failure on a very wet, dark MI road in the middle of nowhere...
ftillier - thank you so much, the warming up quickly makes sense I think, the thermostat likely hasn't opened yet... Your values are significantly lower! Ambient when I did the test was 14C. I will need to check again today. -
Serpentine/Accessory belt failure on a very wet, dark MI road in the middle of nowhere...
The new temperature sensor arrived from from FCP Euro; I measured the resistance across the two terminals and get about 2730 ohms. The old sensor was registering as an open circuit so I guess that gives me my answer about what's broken. Interestingly I get these temperatures once the engine... -
Serpentine/Accessory belt failure on a very wet, dark MI road in the middle of nowhere...
Too late but I don't think it was feasible anyway... Still, something isn't right as I got these fault codes :-(. The good news is that the engine is running and seems to be OK, although it's still early days. P2185-17 and P065C-00; the first is the sensor, the second perhaps an issue with... -
Serpentine/Accessory belt failure on a very wet, dark MI road in the middle of nowhere...
Yep - exactly, I don't see the point in spending lots of $$$ if there's more fundamental issue; the cooling system refresh will all coincide with timing chains as well... I'm ah 102K miles and don't know the history of the parts; chains are slightly noisy! -
2015 LR4 Stalling when cold - Low Fuel Pressure Fuel codes etc.
I feel it takes a little time to gain confidence that a fix works... These trucks are not 4Runners but when they run they're friggin amazing! Good luck and welcome. -
Serpentine/Accessory belt failure on a very wet, dark MI road in the middle of nowhere...
As mentioned previously; when the belt broke it also damaged the coolant temperature sensor found directly below the thermostat; here are some images; for reference you can see the AC compressor behind the connector: The damage is to both the thermostat which can be found here at FCP Euro... -
Serpentine/Accessory belt failure on a very wet, dark MI road in the middle of nowhere...
The new idler pulley (part# LR010725) which is situated behind the viscous fan pulley does indeed measure 70.1mm (which is the same as the original when I measure with my vernier calipers). The width is marginally less. The new pulley is made from Plastic while the old one was steel (the... -
Head Removal
This forum (and all the great folks here :-) ), YouTube, patience, knowing when to walk away and take a break, decent tools that will naturally grow as time goes by, a spare vehicle, a place to work safely and comfortably, a reasonable understanding of how things work and why (YouTube again)... -
Good buyers guide overview
Is this your video? I saw this pop up but didn't get to it yet... Add serpentine belt to the list :ahhhhh: -
Accurate Service History of the Car
Translation from Google: "I would like to get a complete service history, including information about what parts were replaced when servicing the car I bought. Is anyone able to help me get such a report? I am importing a car to Europe from the United States, but unfortunately European service... -
PCV Valve Replacement
Part number appears to be LR133579, I plan to add this to the list! -
Serpentine/Accessory belt failure on a very wet, dark MI road in the middle of nowhere...
Comments posted above about this, in essence, no, it's all on the immediate to do list (along with timing chains) -
Serpentine/Accessory belt failure on a very wet, dark MI road in the middle of nowhere...
Tensioner pulley measures 75.75mm; the idler pulley behind the viscous fan pulley is 70mm. So they're different, I'll measure the new ones when they arrive and report back. -
Transmission taking too long to shift
I'm nodding my head, this is good to hear despite my OCD approach/opinions, I can live with this. - Thank you. -
Serpentine/Accessory belt failure on a very wet, dark MI road in the middle of nowhere...
Here's the parts list and current pricing info (prices are rounded): The broken idler (the bracket I think is OK) LR035555 ($211 at Lake Bluff), this is the full assembly LR010725 is the pulley ($50) Bolt for the same idler Not seeing this yet, not needed if we buy the bracket! The other... -
Serpentine/Accessory belt failure on a very wet, dark MI road in the middle of nowhere...
Yes, it looks identical. The pulley also looks like the idler pulley but as I mentioned above I'll need to measure them to conform the diameter. Thank you for sharing this. -
Serpentine/Accessory belt failure on a very wet, dark MI road in the middle of nowhere...
I just put in an order with Lake Bluff; they're based in IL and were helpful when on the phone. I'm not sure about the idler on the tensioner been the same as the idler on the assembly (they're both flat pulleys); the old pulley on the assembly (the broken one) is metal while the replacement...
