Search results
-
ENGINE SHOT
Was the ticking noise gone after the timing chain replacement? Or was it still ticking. By bearing failure, I assume you mean a rod bearing, right? -
P0442 code and CEL - 2012 LR4
Purge valves do go bad eventually, so even if that turns out not to be your problem, it is not a complete waste to refresh that part. Please do let us know if it works. I was corresponding with someone on another forum about a similar issue - strange behavior after fill-ups - and suspected... -
maintenance schedule
If you have the original papers that came with the car, it’s usually in a booklet called “passport to service” or maybe at the end of the owners manual. Otherwise, if remember correctly, you can create a landrover topix account and the maintenance schedule info is available without a... -
Brake Pad Rattle Advice
I’m not talking about pad knock-back. That has to do with the amount of piston retraction and gives the symptom of different brake pedal travel. My pads simply rattle a bit going over bumps. The pad ears are just loose in the grooves, just like CRYA posted above, because the anti-rattle clips... -
2014 LR4 Water pump/ plumbing status?
That looks like the new style front crossover, so I’m guessing the front crossovers were replaced. I replaced mine at 52K and will probably do it again at 100K, as there is no telling how well the new parts are going to hold up. No way to tell about anything else from the pictures. You... -
Brake Pad Rattle Advice
Right after I posted the above, I tried a google search for coated brake clips. I think this is similar to what I took off my car: https://carlsonqualitybrakeparts.com/brake-hardware/quiet-glide-brake-clips/. No idea if it would help. -
Brake Pad Rattle Advice
I have the same problem - and I believe I used the same pads. I think it’s the new clips, not the pads per se. The clips I took off the car (and discarded) had a coating on one side that I think held the pads better. I remember taking those clips off and thinking - what the hell is that... -
First Oil Change Notes
It occurred to me only after I had gotten the adapter stuck on their pretty good. I should add - when I use the bare tube, I push it on quite far - like maybe 4-5 inches overlap - which probably gives it a little better seal. -
First Oil Change Notes
One of the tubes supplied with the mityvac fits fairly well over the dipstick tube without the adapter. You would think it doesn’t make a tight enough seal, but I’ve done it both ways (with/without rubber adapter) and found it makes little difference. Even using a needle-nose, I‘m paranoid... -
New Owner of 2015 LR4 3.0SC
Yes, you need to remove the supercharger. Parts lists and how-to is found in these threads: https://www.landroverworld.org/threads/how-to-supercharger-removal-rear-crossover-and-passenger-valve-cover.42135/... -
New Owner of 2015 LR4 3.0SC
Welcome and congrats on the purchase. With respect to question 1: No, the water pipes were not updated on your car. In fact, I don’t think the updated pipes came out until around 2018-2019. So, if they were not changed previously, they need to be changed. With respect to question 2: This... -
Ugh. Check engine light. Little help with the codes please
Absolutely agree. Just going through the college thing now with one of my kids. It’s nuts. The prices, the demand, the overcrowding at some schools. Meanwhile skilled trade rates seem to be skyrocketing with no end in demand to be seen. -
Ugh. Check engine light. Little help with the codes please
I believe this is your mid-catalyst sensor. Pretty easy to get to. If you don’t want to wait for the dealer, you should be able to go to an indy with the extended service plan (I don’t think they require the dealer to do it). Replacing the o2 sensor is pretty straightforward, so any mechanic... -
Timing Chain replacement
It’s certainly a short-cut, but looks like there’s enough slack in those chains to get the timing off a tooth if not extremely careful. And, if the car already skipped timing before you got it, this won’t fix it as you can’t re-time the engine this way. And, no - I don’t think the chains can... -
2016 LR4 Coolant Crossover, Water Pump, Thermostat Replacement
There is no part number that I know of. LR doesn’t sell just the isolator. They want to sell the whole snout. The snout is just the front part of the sc with the pulley front drive shaft and drive shaft housing. It bolts onto the body of the sc (and is sealed with RTV). The throttle body... -
How to: Supercharger Removal, Rear Crossover, and Passenger Valve Cover
I know you can remove with throttle body attached. I’m pretty sure you can disconnect the hose at the back and leave that oetiker clamp attached. Definitely can reuse the intercooler gasket. -
ECO Auto Start/Stop Not Available
As far as I know, the sensor on the negative rail of the start battery is the only connection to the BMS, which controls the alternator output based on the battery charge detection. So, disconnecting this is not a good option, and I believe the warning will still pop up. That video posted... -
How to: Supercharger Removal, Rear Crossover, and Passenger Valve Cover
I don’t recall there being a specific torque order for the charger (I think the intercooler had a torque order). I think they just want you to torque the center bolts first, then the outside bolts. On the pins, you would use the threaded ones. No idea on availability, but its super easy to... -
How to: Supercharger Removal, Rear Crossover, and Passenger Valve Cover
Ah, yes - I think it’s called an oetiker clamp. I just studied it a bit and got it off without much problem - can’t remember how exactly right now - pried a tab up I think, maybe while compressing it a bit. Basically, I think it has some hooks on one side and holes on the other that grab the... -
2010 LR4 - L319 with persistent P0018-00 (28) trouble code
I’d say there’s a good chance this is a timing chain issue, since it’s a known issue on this engine and you’ve already ruled out the camshaft position sensor. If the crankshaft position sensor goes bad, I would expect position correlation errors on both banks, not just one. I think there’s... -
FYI: SCV6 cylinder numbering
That’s correct - sc compressing the air also heats it up, and the intercooler tries to bring that compressed air temp down as much as possible, increasing o2 density. If the air is warmer than expected, I assume the engine will compensate with less gas to keep the fuel mixture correct, but the... -
FYI: SCV6 cylinder numbering
i’m not sure why bad aux pump would cause misfire. I understand that it would give the p026a code and run less efficiently, but bad misfire on #6? Has any other work been done recently? Has it overheated or coolant levels dropped? -
2016 LR4 Coolant Crossover, Water Pump, Thermostat Replacement
Definitely need to take the intake manifold off, and you do need gaskets. Looks like I just forgot to put it in the parts list. Those are the only gaskets you should need. Some people replace the intercooler gasket, but it’s not a crush gasket and can be reused (even the manual does not say... -
How to: Supercharger Removal, Rear Crossover, and Passenger Valve Cover
That’s the same kind I use. Different brand. I bought mine at an O’Reilly’s when I had things apart and was way past sick of using a pliers. Made a huge difference. -
Are these two options available with the Gap tool?
As for the button greying out, I guess I’ve never tried activating them on the move, I only know that once the camera screens are open, the cameras keep working and showing visual on the screen while I’m moving. In other words, if I open the camera screen while I’m still, then start driving...
