Search results

  1. powershift

    LR4 Tailgate not opening

    .
  2. powershift

    Front brake pads on 2013LR4 funny looking weight?

    If the weather is bad (wind or overnight rain/snow) then I'll work out of the back of it. I found a comfortable low-profile chair and a desk that fits inside the back. I'm looking forward to it tbh. Normally I work out of a big canvas 8 man tent that I setup an office in that also has windows...
  3. powershift

    Front brake pads on 2013LR4 funny looking weight?

    I swapped the front rotors out and the front squeal went away! At least it went away after bedding them and some initial driving. I'll test it out more tomorrow when I run errands again. I got the pads smoking hot, let them cool and repeated twice. Now just the rears squeal when backing into a...
  4. powershift

    Lr4 Brakes

    Does putting the parking brake into the mounting position back the shoes off further than when the star wheel is backed all the way off?
  5. powershift

    Lr4 Brakes

    Ah, that is probably it. The manual says "Using the Land Rover approved diagnostic system, drive the parking brake to the mounting position." and I researched that to mean to fully retract the parking brake. So that is why the rear rotors were stuck on there.
  6. powershift

    Front brake pads on 2013LR4 funny looking weight?

    The front caliper mounting bracket bolt size is 21mm.
  7. powershift

    Front brake pads on 2013LR4 funny looking weight?

    I did what I could at the time to service the breaks. Security called me out previously for working on it in the parking lot while doing the front cross over, so I was out in the street with cars driving by trying to do the brakes. I'm in the middle of packing up and moving out of my apartment...
  8. powershift

    Lr4 Brakes

    The front rotors were in good condition and I didn't need to replace them nor the pads even though I bought new ones. That is what I get for not checking first. Carfax reported the pads having 20k miles on them but looked like only 10k of wear missing. The front rotor surfaces looked good, no...
  9. powershift

    Front brake pads on 2013LR4 funny looking weight?

    My Ferodo front right vibrates or squeaks. Strange how one front side squeals and the other doesn't. Its quiet when cold too. I'm wondering if the pad clips are tweaked, the vibration damper weight is upside and outside.
  10. powershift

    Tires

    For a treadwear of 620 only getting 18k miles is daylight robbery. I would expect at least 40k mi from them. The Pilot Sport models are good tires, but the life of those would be about 20k miles. Michelln is up to dirty tricks sometimes. I had a Z06 Corvette that came with Z rated Michelins. It...
  11. powershift

    Dual engine air intake channels

    I noticed after the shop that did my timing chain work that my diff breather was missing. Apparently it was stuffed out of the way, but the original location where it was before I brought it in was wrong, illustration reference is here. It is supposed to be mounted to the rad like this:
  12. powershift

    Lr4 Brakes

    It had the round metal weight mounted to the pad backing plate that I installed on the upside and outer side for the fronts. There weren't any shims aside from what was already stuck onto the backing plate for the compound, I guess it could have been a plastic shim. It wasn't bare metal for...
  13. powershift

    Seeking LR4 inline thermostat and crossover pipe Beta Testers

    I'm curious, what material is used to create the new part?
  14. powershift

    Lr4 Brakes

    I put the Ferodo brand compound on today with new metal clips and bolts. I bed them on the existing rotors because I couldn't remove them to put on the new Zimmerman rotors on. I tried beating on the rotor hard with a hammer and my ears started to hurt from the noise so I caved and just cleaned...
  15. powershift

    Aftermarket Carplay/Android Auto

    How did you remove the factory knobs, did you just pry them off with a screw driver?
  16. powershift

    Aftermarket Carplay/Android Auto

    Nice install and the screen is closer to the driver. I had thoughts of a car pc and picked out this monitor and wasn't sure about mounting but saw this beanbag mount. I have bespoke software that uses google maps, a GPS and overlays for public land (BLM/Forest) boundaries and weather so that...
  17. powershift

    Anyone know what this plastic thing is?

    Seems like a better way to go compared to a windshield sticker. We don't have tolls around here in Nevada. The LR4 came from CA and I don't remember traveling on a toll road there. Maybe the Bay Area has them.
  18. powershift

    Anyone know what this plastic thing is?

    I finally got my license plates today and I received the LR4 in July lol. I had been driving around with expired paper plates and cops didn't seem to notice or care. When I first got my LR4 first thing I did was pull the front plate and set it on a shelf. Now I'm re-visting the plate holder so...
  19. powershift

    bad lower ball joint lead to howling?

    It sounds like you discovered a new problem while investigating the howling. I think howling noise would be from the wheel bearing and not the ball joint if you isolated the origin to the wheel. I'd replace the poly bushings and that whole control arm that they came in with a Land Rover brand...
  20. powershift

    Bleeder screw top blew off

    I put my brass one in yesterday
  21. powershift

    Bleeding brakes and brake reservoir

    I took it back to them and they got more of the dirty fluid out. It looks better.
  22. powershift

    Bleeder screw top blew off

    If you drill it put a strong vacuum nozzle against it so the material doesn't get into the cooling channels.
  23. powershift

    Think these will fit?

    The spacers also affect the wheel bearings and can wear them out prematurely.
  24. powershift

    Vacuum pump leak

    It stank on the way home after they replaced the part, but before I left he said to give it 3 days for the residue to burn off. He also checked the valve covers and there wasn't any oil residue. I'm not that hopeful tbh but I won't know until I give it more time.
  25. powershift

    Vacuum pump leak

    I agreed to $990 for the repair. I didn't think it through and thought I'd need to do hydraulic work. It doesn't require bleeding the brakes so now I'm regretting that badly lol. At least they will stand behind their work. And the last shop that did my control arms said I needed tie rods. I...
View older results

Latest posts

Members online

Total: 525 (members: 4, guests: 521)

Forum statistics

Threads
36,717
Posts
222,728
Members
30,890
Latest member
Besi

Share this page

Top