Search results
-
-
Should I be concerned? What is this hose?
That's the breather for the front differential. Doesn't plug into anything.- Rover Range
- Post #2
- Forum: LR4
-
p003c
Usually caused by low oil levels. Change the two cam phaser solenoids- rear of cylinder heads. And do an oil and filter change.- Rover Range
- Post #2
- Forum: LR4
-
Troubleshooting coolant vacuum fill failure
It is difficult to blow a hose off. I'm betting, it wasn't securely attached.- Rover Range
- Post #20
- Forum: LR4
-
Another weird post-repair issue/question: door light
The connector goes to the mirror assembly. For vehicles that have different options in the mirror, like wade sensing.- Rover Range
- Post #3
- Forum: LR4
-
In Control app not connecting to 2021 Defender
Go to the sales department and see if they have a Concierge person. That person will set up your account and activate it. The previous owner's info will have to be deleted.- Rover Range
- Post #2
- Forum: Defender
-
Fuel Gauge Reading Off
The fuel tank is roughly four feet long. Two gallons is not going to raise the fuel level that much.- Rover Range
- Post #3
- Forum: LR4
-
-
SC V6 Overheat Spike at Highway Speeds
Thermostat would be the most likely cause.- Rover Range
- Post #2
- Forum: LR4
-
Increasing approach angle?
On the ride height switch it self. Orange light. Position flashes until selected height reached.- Rover Range
- Post #12
- Forum: LR4
-
Increasing approach angle?
All LR4s can do this. You have to wait until the suspension has completed the raising process in off road mode. The raising indicator light has to be off. All doors closed.- Rover Range
- Post #9
- Forum: LR4
-
Increasing approach angle?
Once the suspension is in in extended off road mode. You can get additional ride height. The additional lift can be requested once the height change LED has turned off. Press and hold the air suspension switch in the up position for 3 seconds while depressing the brake pedal. A chime from the...- Rover Range
- Post #7
- Forum: LR4
-
Troubleshooting coolant vacuum fill failure
Vacuum filling is always the best choice. There are so many coolant pipes, with high and low passages. Vacuum filling assures a complete fill.- Rover Range
- Post #6
- Forum: LR4
-
Troubleshooting coolant vacuum fill failure
I would fill the cooling system, then do a pressure test. That way you can see where the coolant leak is. Using WD40 to lube the o-rings is a no no. Some of the o-rings in the cooling system don't like WD 40. That would cause the o-rings to swell up and leak.- Rover Range
- Post #2
- Forum: LR4
-
Air Conditioner Help
Low freon levels would cause the issue you described.- Rover Range
- Post #2
- Forum: LR4
-
Persistent misfire under load only
When you have a misfire, the PCM cuts off the injector to that cylinder. So no raw fuel is going into the cat convertor. When you erase the DTC, the PCM is starting fresh. Until the misfire is detected again.- Rover Range
- Post #15
- Forum: LR4
-
Where is this supposed to be bolted? (Part #EH22-13N850-FC)
There's a plastic wiring tray that runs across the bottom of the windshield cowl. The eyelet end attaches to a stud on the left side of the tray. Some vehicle have a stud under the windshield cowl, that the wire would be attached to. It's there for static interference from the ignition coils.- Rover Range
- Post #4
- Forum: LR4
-
Help needed with continued errors
99% of those DTCs are "ghost DTCs." Clear all the DTCs and drive the vehicle until you issue comes up. Then retest.- Rover Range
- Post #3
- Forum: LR3
-
Should I Rebuild?
Contact local dealer. This is the price we quoted a customer.- Rover Range
- Post #10
- Forum: LR4
-
Should I Rebuild?
FYI. You can purchase a reman 5.0L from JLR for $10k. :rock:- Rover Range
- Post #8
- Forum: LR4
-
Hardware key issue
Pop the cover off the driver door handle to reveal the key slot. Open the driver's door. Inside the rear part of door, at the outside door handle level. Pop the little round cap off. Allows access to door lock tumbler. Take a T25 Torx, remove the bolt. NOT all the way out. Slide the lock...- Rover Range
- Post #5
- Forum: LR4
-
-
2013 LR2 parking brake switch removal
Floor console has to be removed. Remove shifter knob. Lift up on the shifter bezel (snaps in). Remove coin tray and vertical cover at rear of console. Remove two screws. Unplug connector. Remove two screws under HVAC controls. Remove two screws in open compartment at front of console. Console...- Rover Range
- Post #2
- Forum: Introduction
-
P0526-17 (28) Fan speed sensor circuit - General electrical failure - circuit voltage above threshold
Any tool other than OEM is considered generic. Although, the OEM LR tool is suspect at times. I have a small MAC Tool scanner. It does an OK job. A Snap On scanner is very spendy. But, probably one of the best.- Rover Range
- Post #8
- Forum: LR4
-
P0526-17 (28) Fan speed sensor circuit - General electrical failure - circuit voltage above threshold
Generic scanners can send you on a wild goose chase. Pesky little elves, that come fix your car in the middle of the night.....:beer:- Rover Range
- Post #6
- Forum: LR4
