avslash
Full Access Member
This straight from the horse's mouth (Service manual)
29. CAUTION: Be prepared to collect escaping
coolant.
Fill the coolant expansion tank until coolant appears
through the bleed ports.
9.
Set the 10. heater controls to maximum.
Start the engine and continue to fill the coolant until the maximum
level is reached.
11.
12. Increase the engine speed to 1500 rpm.
Check if the front heater is warm after 2 minutes, if warm proceed to
step 15.
13.
If not, turn the engine off for 10 seconds and then start the engine
and return to step 12.
14.
Once the front heater is warm, check if the rear heater is warm (if
equipped). If no heat is felt, increase the engine speed to 3000 rpm
for 30 seconds and return to idle.
15.
Once heat is felt at the rear heater, continue filling with coolant
until the level stops dropping and top up to 65mm below rim (to top
rib on back of the coolant expansion tank).
16.
37. CAUTION: Correct installation of the Coolant
expansion tank cap can be obtained by tightening the
cap until an audible click is heard.
17.
18. Switch the heater off.
19. Raise the engine speed to 2000 RPM for eight minutes.
40. CAUTION: Switch off the engine and allow the coolant
temperature to go cold.
Switch the engine off and allow to cool.
20.
Visually check the engine and cooling system for signs of coolant
leakage.
21.
42. WARNING: When releasing the cooling system pressure,
cover the coolant expansion tank cap with a thick cloth.
• CAUTIONS:
Since injury such as scalding could be caused by escaping
steam or coolant, make sure the vehicle cooling system is cool prior
to carrying out this procedure
Make sure the coolant level remains above the "COLD FILL
RANGE" lower level mark.
• NOTE: When the cooling system is warm, the coolant will be
approximately 10mm above the upper level mark on the expansion
tank with the cap removed.
Check and top-up the coolant if required.
22.
29. CAUTION: Be prepared to collect escaping
coolant.
Fill the coolant expansion tank until coolant appears
through the bleed ports.
9.
Set the 10. heater controls to maximum.
Start the engine and continue to fill the coolant until the maximum
level is reached.
11.
12. Increase the engine speed to 1500 rpm.
Check if the front heater is warm after 2 minutes, if warm proceed to
step 15.
13.
If not, turn the engine off for 10 seconds and then start the engine
and return to step 12.
14.
Once the front heater is warm, check if the rear heater is warm (if
equipped). If no heat is felt, increase the engine speed to 3000 rpm
for 30 seconds and return to idle.
15.
Once heat is felt at the rear heater, continue filling with coolant
until the level stops dropping and top up to 65mm below rim (to top
rib on back of the coolant expansion tank).
16.
37. CAUTION: Correct installation of the Coolant
expansion tank cap can be obtained by tightening the
cap until an audible click is heard.
17.
18. Switch the heater off.
19. Raise the engine speed to 2000 RPM for eight minutes.
40. CAUTION: Switch off the engine and allow the coolant
temperature to go cold.
Switch the engine off and allow to cool.
20.
Visually check the engine and cooling system for signs of coolant
leakage.
21.
42. WARNING: When releasing the cooling system pressure,
cover the coolant expansion tank cap with a thick cloth.
• CAUTIONS:
Since injury such as scalding could be caused by escaping
steam or coolant, make sure the vehicle cooling system is cool prior
to carrying out this procedure
Make sure the coolant level remains above the "COLD FILL
RANGE" lower level mark.
• NOTE: When the cooling system is warm, the coolant will be
approximately 10mm above the upper level mark on the expansion
tank with the cap removed.
Check and top-up the coolant if required.
22.